router behind router error 2wire Oakdale Wisconsin

Over 15 years of website design experience. We provide quality web design/redesign and eCommerce sites at prices you can afford. Additionally we offer search engine optimization, internet marketing, Custom grapic and logo design, print media, computer repair assistance, document typing and editing services and much more. Call or visit us online today for a free quote.

Address 914 Kristi Ln, Tomah, WI 54660
Phone (608) 567-4157
Website Link http://www.alphawebsolutions.net
Hours

router behind router error 2wire Oakdale, Wisconsin

Bao Shuming 12 March 2013 23:07:36 CarRamRod10 said:Has anyone accomplished this feat. I told it to use ethernet connection rather than wireless. It will connect to TC and it shows up under shared, etc. I am currently doing my first back up...

Helpful (0) Reply options Link to this post Page 1 Next This site contains user submitted content, comments and opinions and is for informational purposes only. Having two different wireless LANs in the same house can create confusion, and the Time Capsule LAN is much faster anyway . . . Any other connection method is going to be very slow by comparison. Many thanks Scott Rose permalink* September 28, 2012 10:35 AM Whatever you want it to be… you're effectively just connecting your Airport to a "dumb modem" at that point.

All settings of the 7550 were the default at this point. The WAN port is not used. 4. There is a nice article from Cisco/LinkSys called "Cascading (Connecting) a Linksys router to another router" about the two ways to cascade two routers, LAN-to-LAN and LAN-to-WAN. You need to know how you connect to the internet.

AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. Basically you have to turn off the U-verse Firewall. I really want to use the Airport for DHCP and firewall management but the problem is my iPhone's Uverse app can no longer see the Uverse DVR if I have it You can plug any ethernet able device (including a PC) into the to get them on the network.

Leave the "Alt Line" port empty. I have spent hours trying to setup a netgear wireless behind a 2WIRE, the ones used by ATT's fiber service and can't get it done. however, the reason i am still researching this is because my Remote Desktop doesn't work. and FAQs Helps you find the right support you need from Contact nos.

Thanks in advance. I obfuscated the public values here for obvious reasons. The first router is your Gateway to the internet so it's IP address must be placed as Dns on the second router. Go to your web browser and type in 192.168.1.254, which will take you to the 2Router administration page. 3.

Attention to Telemetry updates 'preview' for Win 7 / 8.1 [Microsoft] by chachazz280. I sure wish I could disable that PAP2 routing stuff then. THIS IS THE EASIEST WAY TO DO THIS!! Will this method work for any n router out there?

When he saw my Linksys router laying nearby, he said "With this beauty right here..." and he showed me the 2Wire device, "... Cable any of the Time Capsule ethernet ports to the ethernet LAN port on the 2Wire router. Brilliantly easy! Using airport utility 6.1, I edited the airport extreme settings. (Allow setup over WAN), I verified the router address which points to the Uverse router, and noted the IPv4 address and

solution Will a router speed up my internet speed on an at&t 2wire? Related resources Seting up A 2nd router behind an AT&T 2Wire UVerse Router - Forum Seting up A 2nd router behind an AT&T 2Wire UVerse Router - Forum Router behind Uverse Quicken for Lion: Why Does Intuit Hate Mac Users? You can verify that the 2Wire setup is correct by going to the Status page under the Settings and Firewall sections and seeing that the DD-WRT device is listed under the

The other end went into the WAN port on the Asus. Change the IP address of the 2nd router to 192.168.1.2. This gives a lower power/shorter range, slightly more secure 2nd wireless network with SSID #2. The next step is to connect to the 2Wire device.

This is set up as two network addresses, 192.168.1.0 and 192.168.2.0 (two Class C networks). (See: http://www.ralphb.net/IPSubnet/ for IP Address Subnetting Tutorial). All I wanted to do was something very simple for my clients: Put a router (the 2Wire 3800HGV-B router, commonly used for AT&T U-Verse installations) into bridge mode, so that an Apple link. I started a back up and things were going OK.

Just enter your address, and we'll e-mail you a link to reset your password. Someone mentioned about the Subnet Mask being different with ATT and sure enough it was. So then I went in on WAN setting and manually changed it to match the IP address of the ATT modem, Subnet Mask, DNS 1 and DNS 2. I didn't get the Uverse message or the suggested fixes.

Where are these switches for turning on the components? Use your computer to get on the same network as your 2Wire router, either wireless or hardwired in with an Ethernet cable. 2. kill trees [HomeImprovement] by abrogard7289. Here are the directions: http://www.jaynath.com/2011/01/setting-up-tomato-router...

Can't find your answer ? no sense loading the 2WIRE router with less efficient wireless traffic. Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses! I unplugged the Ethernet cable from the Linksys and connected it to one of the LAN ports on the 2Wire.

I tried doing it with the WAN port as a real router, but I was never able to get my firewall settings to open the needed ports correctly, so I gave