remote communication error. target disconnected. connection reset by peer Hermleigh Texas

Address 1354 N Avenue R, Snyder, TX 79549
Phone (325) 436-4244
Website Link
Hours

remote communication error. target disconnected. connection reset by peer Hermleigh, Texas

For bug reporting instructions, please see: . ./obj/local/armeabi/gdb.setup:4: Error in sourced command file: Remote communication error. How do you tell it's halting? Polling again in 100ms [Remote target] #1 stopped. HTH -- Be free, use free (http://www.gnu.org/philosophy/free-sw.html) software!

From: Kiwamu Okabe - 2014-11-12 11:15:39 Hi Paul, On Thu, Nov 6, 2014 at 5:29 PM, Paul Fertser wrote: >> $ arm-none-eabi-gdb build/hacker-emblem.elf >> (gdb) tar ext :3333 >> I'm using following firmware running on my STM32F030F4P6 board. From: Paul Fertser - 2014-10-30 13:22:29 On Thu, Oct 30, 2014 at 10:15:18PM +0900, Kiwamu Okabe wrote: > Info : stm32f0x.cpu: hardware has 4 breakpoints, 2 watchpoints > ``` > So, this means you started the firmware and it's running now, I do not see any single error or problem in your output. -- Be free, use free (http://www.gnu.org/philosophy/free-sw.html) software!

The target is already running. And I believe STLINK v2 gives power to the board, without any battery. The results might differ compared to plain JTAG/SWD adapter speed: 1000 kHz adapter_nsrst_delay: 100 srst_only separate srst_nogate srst_open_drain connect_assert_srst Info : clock speed 1000 kHz Info : STLINK v2 JTAG v16 Re: [OpenOCD-user] How do I support STM32F030F4P6 on openocd?

http://www.seeedstudio.com/depot/FSM55-LED-Matrix-Display-p-2121.html However, the project does not support openocd. windows NT detected TRACELINK detected - Flash version 1.300 Device is K10FX512 ... 16:12:26 Server Running on 192.168.1.197:7224 Session Started Session Ended... Browse other questions tagged android android-ndk or ask your own question. Error: attempted 'gdb' connection rejected ``` Chip id = 0x0?????

write and recv vs. I suggest you either add a gdb-attach hook to openocd to "halt" the target or add "init; halt" to config or command line to do it on start, that should help. Please check out our website on the GDB server and grab the latest version that we have. There should be two Debug Configurations available to your Java / C++ Native project.

http://www.gniibe.org/memo/development/fsm-55/fsm-55-testplan.html https://www.flickr.com/photos/masterq/15297988789/ https://www.flickr.com/photos/masterq/15484536002/ Thank's, -- Kiwamu Okabe at METASEPI DESIGN Re: [OpenOCD-user] How do I support STM32F030F4P6 on openocd? mailto:[email protected] To type it faster, "tar ext :3333" is enough. Target disconnected\.: Connection reset by peer\.} Attachment: send.c Description: Text document Follow-Ups: Re: [testsuite patch] race: server-kill.exp: Connection reset by peer [Re: [patch+7.6] Fix 7.5 regression crashing GDB if gdbserver dies]

This GDB was configured as "--host=x86_64-linux-gnu --target=arm-linux-android". How to adjust UI scaling for Chrome? I can load firmware on gdb! Alphabet Diamond Generating a sequence of type T at compile time Disproving Euler proposition by brute force in C Code Golf Golf Golf Reverse puzzling.

read also make no difference there. s f. http://www.st.com/web/catalog/tools/FM146/CL1984/SC724/SS1677/PF251168 http://www.aliexpress.com/item/Free-Shipping-1SET-ST-Link-st-link-V2-for-STM8S-STM8L-STM32-Cortex-M0-Cortex-M3/1619197946.html How do I support STM32F030F4P6 on openocd? Re: [OpenOCD-user] How do I support STM32F030F4P6 on openocd?

Waiting for target to halt. more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed Also, are you sure the firmware you flash is suitable for your target and it doesn't enable any sleep modes or disable JTAG pins? Join them; it only takes a minute: Sign up ndk-gdb and ndk-gdb.py Errors up vote 4 down vote favorite I want to use ndk-gdb to debug my native code on Android

send vs. From: Kiwamu Okabe - 2014-11-12 12:05:34 Hi all, BTW. I've not yet found a way to setup through the actual source yet, if anyone does please post here. reset () at sys.c:699 699 asm volatile ("cpsid i\n\t" /* Mask all interrupts. */ ## Case B: Use halt ### Console B-1 $ openocd --version |& head -1 Open On-Chip Debugger

Debug your application using its Native debugger that you created in the Sequoyah guide. more hot questions question feed default about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Page generated in 0.11106 seconds .:: Contact :: Home ::. Something that used to work is probably an issue with settings that you may have changed.You should give me more details like what other settings you are using.

Bitwise rotate right of 4-bit value Are there any pan-social laws? But there are errors. > ndk-gdb --verbose --force --start WARNING: The shell running this script isn't bash. http://openocd.sourceforge.net/doc/html/CPU-Configuration.html http://openocd.sourceforge.net/doc/html/GDB-and-OpenOCD.html Then, I tried following commands, however, can't get success.... ## Case A: Use reset init ### Console A-1 $ openocd --version |& head -1 Open On-Chip Debugger 0.9.0-dev-00184-g885f438 (2014-10-30-21:18) For bug reporting instructions, please see: . ./obj/local/armeabi/gdb.setup:4: Error in sourced command file: Remote communication error.

what was the cause of error ? –user1103138 Mar 26 '12 at 4:31 Read...