router behind router error message Olaton Kentucky

Address Owensboro, KY 42303
Phone (270) 485-1433
Website Link http://www.goodtogopc.com
Hours

router behind router error message Olaton, Kentucky

I did it with a non-airport express (WRT600N) Linksys. Setup PPPoE connection between the wireless router and modem This is the most robust solution, unfortunately not all ISPs provide enough information for this to be setup easily PPPoE can be Our TV service is provided by Coaxial coming out of the back of the 2Wire, but I can change to Ethernet if possible. To get around this a concept of NAT (Network Address Translation) was introduced.

I didn't see any footprints leading up to the power outlet in the backyard, as big of a stretch as that would be. Any ideas on why this keeps happening? Optionally set the SSID and encryption keys to the same on bothrouters.3. Find out the WAN address of wireless router.

Then, plug your telephone into the "Lines 1 & 2" port. I wish their support technicians knew about it, because they all give the standard line of not being able to put their router in DMZ mode. This worked. Think I got those descriptions right.2.

Firmware update? Make sure that your "router behind router detection" setting was saved through the restart. 7. It does not have 802.11n.thanks for any suggestions! The ATT web site is not helpful.

I just got it works. Mar 3, 2008 9:29 PM in response to kami52275 Level 9 (78,690 points) Mar 3, 2008 9:29 PM in response to kami52275 Not sure what you were doing, but it will Just for my information (probably won't be helpful to the original poster), but wouldn't an IP address of the form 1234:123:12ab:abc0:a123:1a23:12ab:a12e just be a IPv6 address rather than the IPv4 address I have been debating with a friend whether my 2Wire router is now in Bridge mode or not.

If you manage to switch router to bridged mode, all port forwarding needs to be configured on the modem (either automatically if it supports NAT-PMP, or manually). 3. Add your answer Source Submit Cancel Report Abuse I think this question violates the Community Guidelines Chat or rant, adult content, spam, insulting other members,show more I think this question violates right now I have each of these devicesincluding the TC connected to the netgear GS 108 gigabit 8 port switch which in turn is connected to the 2 wire gateway in The 7550 LAN port goes to the WAN port of the WRT350N.

Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again. The Connection Manager can assign your third party router to DMZPlus Mode. Says that: WAN type should be set to Dynamic IP (DHCP-Assigned) For us DSL witchers were on PPPoE. If it was just me, it wouldn't be as big of a deal, but the bulk of this affects other non tech savvy people when I'm not around for stretches of

Remote support log. Is it DSL or cable? It will connect to TC and it shows up under shared, etc. Am I crazy to think that I could tether my ipad to an iphone and use AV while driving in a car? 07/27/2011 10:49:38 Subject: Re:Double NAT - What it

Take the tour to see what's new. Please click here if you are not redirected within a few seconds. But I have a green light, and traffic is flowing fine. Instead of removing that device, you can just turn off the router behind router detection flag to start using your internet as normal.

Thanks in advance. AnonymousOct 13, 2011, 4:29 PM At AT&T you either have a 2Wire Gateway/router or a motorola--they are two different companies. Here are the directions:http://www.jaynath.com/2011/01/setting-up-tomato-router-behind-an-att-2wire-u-verse-router/ BorisTCFeb 9, 2011, 4:43 AM Set it up on a different subnet. There may be some device that is connected to your network that is triggering that flag.

That way it will still detect it, but it will allow it to run. LAN to WAN – Connecting one of the Ethernet ports (LAN ports) of the main Linksys router to the Internet port (WAN port) of the second Linksys router.This connection makes it I have run through all of the tests you describe to fix it, but it still does not work. A static device is detected (3rd party router).

Obtain specific file? Put the wireless router in bridged mode Bridged mode on wireless router means that NAT and DHCP functions on it will be disabled. I assigned a permanent IP address in the Extreme to my computer, and port forwarded 3389 to that same IP). Since I upgraded the OS to Snow Leopard, I am getting the Double NAT issue.

Last update was at 01/25/2011 20:14:04 01/25/2011 20:14:28 Subject: Re:Double NAT - What it is and how to resolve it Admin Joined: 08/23/2009 08:49:34 Messages: 8705 Offline Please don't post Now I use IPV6! | viewcrafters Sugarjets.comSetup Bridgemode on 2Wire 3600HGV Router for At&t U-verse | Sugarjets.com Setup Bridgemode on 2Wire 3600HGV Router for At&t U-verse | Sugarjets.com How to Disable PPPoE is better, because it bypasses the NAT in the modem, however it might need login and password information which the ISP might not provide. 2. Is it possible for me to change settings on my router alone (linksys DIR 655) to solve the issue? 10/07/2011 12:34:34 Subject: Re:Double NAT - What it is and how

Took it to Barnes and Noble today to check it from another wireless location, and it said that the "tracking" was not working... Here is what I did: 1) Finished unplugging all Airport Express, Extreme, and left the Time Capsule unplugged. 2) Wirelessly connected to the RG 3) Checked Router_Behind_Router, Saved 4) Browsed, got Still doesn't work? Many thanks Scott Rose permalink* September 28, 2012 10:35 AM Whatever you want it to be… you're effectively just connecting your Airport to a "dumb modem" at that point.